Page tree

Contact: / /

Skip to end of metadata
Go to start of metadata
  • Compatible with Raspberry Pi Zero,Zero W,3B,3B+,PI4 via the 28-pin connector, With 480 (W) *320(H) Pixels high-resolution; Connects directly to the Raspberry Pi board, no additional cables required, no soldering.
  • Communication between the screen and the Raspberry Pi is interfaced with a high speed 63Mhz SPI connection. Enable the direct memory access(DMA) channel for high-speed data transmission in the kernel, so it can support output higher frame rate than other.
  • On-board capacitive touch controller, allow you to control your raspberry PI by touching the screen with your fingers , Accurate and easy operating.
  • On-board extremely accurate I2C real-time clock (RTC) DS3231 and continuous timing battery backup.
  • Comes with user manual and friendly technology support. For more information please refer to our wiki(view the link on color page comes with the goods).


The 3.5 inch RPI lcd display TFT Capacitive Touch Screen is a display module can be applied to Raspberry pi 3 B+ Pi Zero etc. It can be used as raspberry pi x window display terminals.


  • 1. This RPI lcd display TFT capacity touch screen compatilble with Raspberry pi 3 modle B / Pi 2B / B+ / Pi Zero / etc.
  • 2. 16bit/pixel, 320×480 resolution and large view angle.
  • 3. This RPI lcd display support resistive and capacitive touch specifications, the software fully compatible.
  • 4. This RPI lcd display provide preset raspbian-jessie system image and a separate installation package.
  • 5. This RPI lcd display provide accurate DS3231 RTC unit to ensure that the system time is accurate.
  • 6. LCD Backlight can be controlled.
  • 7. Hardware and software is compatible with any version of the raspberry pi.
  • 8. This RPI lcd display module have the same size as standard raspberry pi.

[Hardware connection:]

The RPI LCD Display TFT Capacity Touch Screen Modules used 28 pins out of raspberry pi 40 pin. When installing the module attention to align the first leg of the raspberry pi and LCD module.

[Packing List:]

  • 1 x Amplifier HIFI AMP Expansion Board; (Note: the raspberry pi 3 board is not included.
  • 1 x 3.5 Inches 320×480 TFT Display Capacity Touch Screen
  • Note: The raspberry pi 3 board is not included.

Quick Start:

git clone

Full User Manual,Ready-Made System,Software

  • No labels


  1. Anonymous

    Connecting this to a pi-zero-W using the provided "buster" images it is painting to the screen, but the screen contents are corrupt.  You can barely make out that the cursor moving in 3 places at the same time within the noise on the screen.

    I've tried to modify the speed/fps settings in boot/config.txt thinking perhaps the pizero just couldn't keep up with the high speed selected by default for the SPI interface, but this brings little to no change.

    Is there something different that must be done for the pi-zero?

    1. Dear Customer,
      This device not support pi zero for for now. The drivers is for specific hardware and kernel version.

      1. Anonymous

        From above:


        • 1. This RPI lcd display TFT capacity touch screen compatilble with Raspberry pi 3 modle B / Pi 2B / B+ / Pi Zero / etc.

        Do you have plans to provide this or source/specs so that appropriate kernel modules can be built?

      2. Anonymous

        How about producing the source code?

        Some of us bought these displays because you own product page says it works with the Pi Zero, but the provided modules are only for the Pi3 & 4. This is not acceptable.

        Given the source code, the community could help provide the needed port to the Pi Zero.

  2. Anonymous

    If I want to install this on a current, fresh Buster "lite" image, what software needs to be installed in addition to Inno-Maker's drivers?

  3. Anonymous

    Linux version 5.10.11-v7+ is now being rolled out via apt. When can we expect to see updated Inno-Maker display drivers?

  4. Anonymous

    Waiting for driver 5.10.14!

    Recently bought your LCD and no driver is out to work that thing ;(

  5. Anonymous

    Please provide source code to drive and full details... and they we can use this on a variety of hardware (eg Raspberry Pico) and your sales will increase!

  6. Anonymous

    >>> Full User Manual,Ready-Made System,Software


    The software folder is empty  !

  7. Anonymous

    Mt display shows a white display, where do I go for trouble shooting? this was tried on a pi3, pi4 with corrct version of teh OS and following the directions carefully.